如果更改proe自带公差表？

gp_1125

如果更改proe中的公差表内容？
还有就是公差表中这些数字都代表什么意思？

一下是代码:


!# Pro/TABLE
!# Pro/TABLE  TM  Version E-01-41  (c) 1988-93 by Parametric Technology Corporation  All Rights Reserved.
! [] S 92;
![] W 10;
![A] W 11;
![B] W 12;
![C] W 12;
![D] W 12;
![E] W 12;
![F] W 12;
![G] W 12;
! MODIFICATIONS:
!  24-Jul-95  G-01-01  JAM   $$1  Fixed value for 14 deviations, size 2000-2500.
"! Any cell preceeded by ! will be ignored"
"! Any cell preceeded by # will be treated as a comment"
"! All comments must be at the beginning of the file before table header"
"ISO Tolerance table"
"Table_Type" "Shafts"
"Table_Name" "h"
"Table_Unit" "micrometer"
"Range_Unit" "millimeter"
"Basic Size" 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 " "
"- -  3" "\"0/-0.8" "\"0/-1.2" "\"0/-2" "\"0/-3" "\"0/-4" "\"0/-6" "\"0/-10" "\"0/-14" "\"0/-25" "\"0/-40" "\"0/-60" "\"0/-100" "\"0/-140" "\"0/-250" "\"0/-400" "\"0/-600" "\"-" "\"-"
"3 -  6" "\"0/-1" "\"0/-1.5" "\"0/-2.5" "\"0/-4" "\"0/-5" "\"0/-8" "\"0/-12" "\"0/-18" "\"0/-30" "\"0/-48" "\"0/-75" "\"0/-120" "\"0/-180" "\"0/-300" "\"0/-480" "\"0/-750" "\"0/-1200" "\"0/-1800"
"6 - 10" "\"0/-1" "\"0/-1.5" "\"0/-2.5" "\"0/-4" "\"0/-6" "\"0/-9" "\"0/-15" "\"0/-22" "\"0/-36" "\"0/-58" "\"0/-90" "\"0/-150" "\"0/-220" "\"0/-360" "\"0/-580" "\"0/-900" "\"0/-1500" "\"0/-2200"
"10 - 18" "\"0/-1.2" "\"0/-2" "\"0/-3" "\"0/-5" "\"0/-8" "\"0/-11" "\"0/-18" "\"0/-27" "\"0/-43" "\"0/-70" "\"0/-110" "\"0/-180" "\"0/-270" "\"0/-430" "\"0/-700" "\"0/-1100" "\"0/-1800" "\"0/-2700" " " " " " "
"18 - 30" "\"0/-1.5" "\"0/-2.5" "\"0/-4" "\"0/-6" "\"0/-9" "\"0/-13" "\"0/-21" "\"0/-33" "\"0/-52" "\"0/-84" "\"0/-130" "\"0/-210" "\"0/-330" "\"0/-520" "\"0/-840" "\"0/-1300" "\"0/-2100" "\"0/-3300"
"30 - 50" "\"0/-1.5" "\"0/-2.5" "\"0/-4" "\"0/-7" "\"0/-11" "\"0/-16" "\"0/-25" "\"0/-39" "\"0/-62" "\"0/-100" "\"0/-160" "\"0/-250" "\"0/-390" "\"0/-620" "\"0/-1000" "\"0/-1600" "\"0/-2500" "\"0/-3900"
"50 - 80" "\"0/-2" "\"0/-3" "\"0/-5" "\"0/-8" "\"0/-13" "\"0/-19" "\"0/-30" "\"0/-46" "\"0/-74" "\"0/-120" "\"0/-190" "\"0/-300" "\"0/-460" "\"0/-740" "\"0/-1200" "\"0/-1900" "\"0/-3000" "\"0/-4600"
"80 - 120" "\"0/-2.5" "\"0/-4" "\"0/-6" "\"0/-10" "\"0/-15" "\"0/-22" "\"0/-35" "\"0/-54" "\"0/-87" "\"0/-140" "\"0/-220" "\"0/-350" "\"0/-540" "\"0/-870" "\"0/-1400" "\"0/-2200" "\"0/-3500" "\"0/-5400"
"120 - 180" "\"0/-3.5" "\"0/-5" "\"0/-8" "\"0/-12" "\"0/-18" "\"0/-25" "\"0/-40" "\"0/-63" "\"0/-100" "\"0/-160" "\"0/-250" "\"0/-400" "\"0/-630" "\"0/-1000" "\"0/-1600" "\"0/-

wyg091803

没必要去更改Pro/E自带的公差表吧，它跟国标并没有冲突，选用哪种基本偏差代号和公差等级看你的设计意图来定。需要提醒的是必须在三维环境下先加载公差表，才能在绘图中标注基本偏差代号和公差等级，也可以和极限偏差一起标。

[ 本帖最后由 wyg091803 于 2010-5-5 23:36 编辑 ]

gp_1125

我跟国标对照了一下
貌似proe里面的公差表对照起来不一致
所以要更改呢

野火

哪些会不一致呢？

Senna

wyg091803 发表于 2010-5-5 23:24
没必要去更改Pro/E自带的公差表吧，它跟国标并没有冲突，选用哪种基本偏差代号和公差等级看你的设计意图来 ...

请问怎样在三维环境下加载公差表？

284088231

Senna 发表于 2015-8-28 23:28
请问怎样在三维环境下加载公差表？

文件-准备-模型属性-公差-更改-公差表

fuguangyi

如果你一定要改公差表，参考下面动画，因为有大小限制，录制的短点

SYLY

感谢分享，好人一生平安！！